Nintendo DS Case
45Guide replace a case of Nintendo DS
HTML clipboard
Did you accidentally on the Nintendo DS in the hand (s), which fell heavily to the ground and broke a hinge or a nasty scratches visible on your Nintendo DS case? From those who curse you, be assured that it could replace the Nintendo DS case on its own. But beware, it is hard work. Special tools and patience. If you do not think you have what it takes, it is always better to send it to the store closest to repair confidence.
If you have the courage, which have to do, we will start. If you are calm and ready to hide their Nintendo DS case, place a cloth or towel at the base and in a flat worth on the screws.
Now turn the DS, so the back can see straight up. First, remove the two rubber feet at the top. Then screw the battery compartment in the lower right corner, two screws on the left side and screws on the SD card slot. Remove the battery, remove the screw and the inside cover. When all the screws are placed on the plate, carefully remove the back. Remove all parts of the body, but be careful when removing the shoulder buttons, because they have springs that can jump.
Remove the white and black son in the vicinity of the SD card slot, and remove the black under the slot on the other side. Then remove the screws on each side. You can view the board from the other half of the bottom of the Nintendo DS case.
The two screws on the buttons above and turn ABXY the black bar above the pressure pad to the top of the flat connection and carefully remove the soil. Clear Flag. Insert the ribbon cable into the thin slot, press the left, while the conservative right shell ribbon cable at the same time. Remove the bottom from the top of the Nintendo DS case and set aside.
Turn your attention to the front of the field. Slide the adjustment of the angle to the left, rolling the flat wire and remove the ring on the other side. Then look on the top screen. There are four screws under the carpet on every corner of the screen above, hidden, remove the cover and screws. It's a little tricky, so take your time.
When finished, press the tip with the thumb on both sides of the screen and down with your index finger and push up. You should be able to open the upper shell. Roll the flat wire and push it right should take. Congratulations! Now you can play your Nintendo DS each case. Please install according to a back room.
Guide replace a case of Nintendo DS
Did you accidentally on the Nintendo DS in the hand (s), which fell heavily to the ground and broke a hinge or a nasty scratches visible on your Nintendo DS case? From those who curse you, be assured that it could replace the Nintendo DS case on its own. But beware, it is hard work. Special tools and patience. If you do not think you have what it takes, it is always better to send it to the store closest to repair confidence.
If you have the courage, which have to do, we will start. If you are calm and ready to hide their Nintendo DS case, place a cloth or towel at the base and in a flat worth on the screws.
Now turn the DS, so the back can see straight up. First, remove the two rubber feet at the top. Then screw the battery compartment in the lower right corner, two screws on the left side and screws on the SD card slot. Remove the battery, remove the screw and the inside cover. When all the screws are placed on the plate, carefully remove the back. Remove all parts of the body, but be careful when removing the shoulder buttons, because they have springs that can jump.
Remove the white and black son in the vicinity of the SD card slot, and remove the black under the slot on the other side. Then remove the screws on each side. You can view the board from the other half of the bottom of the Nintendo DS case.
The two screws on the buttons above and turn ABXY the black bar above the pressure pad to the top of the flat connection and carefully remove the soil. Clear Flag. Insert the ribbon cable into the thin slot, press the left, while the conservative right shell ribbon cable at the same time. Remove the bottom from the top of the Nintendo DS case and set aside.
Turn your attention to the front of the field. Slide the adjustment of the angle to the left, rolling the flat wire and remove the ring on the other side. Then look on the top screen. There are four screws under the carpet on every corner of the screen above, hidden, remove the cover and screws. It's a little tricky, so take your time.
When finished, press the tip with the thumb on both sides of the screen and down with your index finger and push up. You should be able to open the upper shell. Roll the flat wire and push it right should take. Congratulations! Now you can play your Nintendo DS each case. Please install according to a back room.
More link :
